Reference: A-XF12V8
Set for locking the camshaft and crankshaft when changing the timing belt. Ability to set the timing to the correct position.
Reference: S-419RA
Widely used not only for automobile repair, daily fastening and hydraulic applications, but also for various applications such as motorcycles, construction machinery and electrical equipment.
Reference: 3286-1
- Diameter : 75 mm. - Maximum speed: 20,000 RPM - Suitable for mini pneumatic cutters. - Thickness 1.8 mm
Reference: 8156-2
Crankshaft locking pin Ford 1.8 D/TD/TDdi/TDCi 2.5 Di-Turbo/TCi
Reference: 10402
PSA's 1.0 and 1.2 Puretech engines use "weltbelt" or wet belt technology where the belt is always in contact with the engine oil. This tool allows you to quickly measure any degradation of the belt.
Reference: F0315
• Joint former based on Acetic Silicone. • High adhesion on non-porous metals. • Resistant up to 315°C. • BLACK color.
Reference: 144309636
Impact and scratch resistant polycarbonate lens. Design for maximum visibility and UV protection. Ideal for jobs with poor visibility. Compliant with EN166.
Reference: 9460
Essential lubricant to always have tools in good working order
Reference: 4874
Made of high performance S2 steel alloy Anchor: 10 mm. Length: 30 mm. Finish: Gray steel Measurement: T50
Reference: 207001
Black insulating tape, made of PVC, resistant to voltage, heat and different acids and alkalines, it is mainly used for electrical insulation, in the automobile, in the electronics and DIY industry. Insulating tape 20 meters long and 19mm wide.
Reference: 9670
The pin allows the pump to be blocked when it is required to be uninstalled or installed, thus avoiding losing its correct adjustment.
Reference: 5184-TS25
1/4" socket wrench with 5-point Tamper-proof Torx tip for Tamper-proof 5-point Torx female screws. Made of hardened and tempered chrome-vanadium steel for greater corrosion resistance. Chrome-plated socket with satin effect and knurled ring for greater grip. Socket square: 1/4" Measurement: TS25. ( Special flowmeters ).
Banner
Set of 18 elements to disconnect pins, electrical connectors. The set is used in the automotive, electrical, boat, etc. industries. Its small size and ergonomic shape allow quick and precise disconnection operations without damaging the connection elements.
Set: 6 tubular ejectors with bayonet base, 6 single keys, 6 double keys
A set of double wrenches with socket diameters: 2/3 / 4.5 / 6 mm
A set of needle wrenches supporting bushing diameters: 0.8 / 1 / 1.2 / 1.4 / 2.0 mm
Simple tubular ejectors for diameters: 2 / 2.6 / 3.2 / 3.9 / 4.9 / 6.2 mm
Reference: 8050
Heats up in 1-3 minutes, stays at 220 degrees continuous, no need to wait for another preheat while doing complicated repairs.
Reference: 418
- finishing for cutting cables - combined tool for insulated and non-insulated terminals - blue soft handles - 3mm thick
Reference: 1426
Made of steel with large vinyl grip handles and hardened and tempered jaws. Ratcheting action ensures consistent crimping tension .
Reference: 7963
- Extra strong stainless steel blades - Handles with non-slip grips for greater comfort - A thin saw-type blade - With cable stripper hole
Reference: 1429
Small head 1.5 cm. Special for entering small spaces, such as vehicle lamp terminals. - suitable for measurement cables: 0.5 - 0.75 - 1.0 - 1.5 - 2.5 - 4.0 - 6.0 - 10.0 - 16.0 mm² - 190mm. long
Reference: 9712
Tool set to remove cables from the terminals without damaging them. They work in conventional terminals as well as Con-Pack & Weather-Pack terminals found in many vehicles.
Reference: A-WS25A
Automatic wire stripper with stripping length adjustment.
Reference: 1419
For non-insulated open terminals 0.5 - 1 - 1.5 - 2.5 - 4 - 6 mm² Length 215mm Gross weight 510g
Set of 18 elements to disconnect pins, electrical connectors. The set is used in the automotive, electrical, boat, etc. industries. Its small size and ergonomic shape allow quick and precise disconnection operations without damaging the connection elements.
