Reference: A-XF12V8
Set for locking the camshaft and crankshaft when changing the timing belt. Ability to set the timing to the correct position.
Reference: S-419RA
Widely used not only for automobile repair, daily fastening and hydraulic applications, but also for various applications such as motorcycles, construction machinery and electrical equipment.
Reference: 3286-1
- Diameter : 75 mm. - Maximum speed: 20,000 RPM - Suitable for mini pneumatic cutters. - Thickness 1.8 mm
Reference: 8156-2
Crankshaft locking pin Ford 1.8 D/TD/TDdi/TDCi 2.5 Di-Turbo/TCi
Reference: 10402
PSA's 1.0 and 1.2 Puretech engines use "weltbelt" or wet belt technology where the belt is always in contact with the engine oil. This tool allows you to quickly measure any degradation of the belt.
Reference: F0315
• Joint former based on Acetic Silicone. • High adhesion on non-porous metals. • Resistant up to 315°C. • BLACK color.
Reference: 144309636
Impact and scratch resistant polycarbonate lens. Design for maximum visibility and UV protection. Ideal for jobs with poor visibility. Compliant with EN166.
Reference: 9460
Essential lubricant to always have tools in good working order
Reference: 4874
Made of high performance S2 steel alloy Anchor: 10 mm. Length: 30 mm. Finish: Gray steel Measurement: T50
Reference: 207001
Black insulating tape, made of PVC, resistant to voltage, heat and different acids and alkalines, it is mainly used for electrical insulation, in the automobile, in the electronics and DIY industry. Insulating tape 20 meters long and 19mm wide.
Reference: 9670
The pin allows the pump to be blocked when it is required to be uninstalled or installed, thus avoiding losing its correct adjustment.
Reference: 5184-TS25
1/4" socket wrench with 5-point Tamper-proof Torx tip for Tamper-proof 5-point Torx female screws. Made of hardened and tempered chrome-vanadium steel for greater corrosion resistance. Chrome-plated socket with satin effect and knurled ring for greater grip. Socket square: 1/4" Measurement: TS25. ( Special flowmeters ).
Banner
3 males: Initial, central and finishing
For thread/thread pitch: M12 x 1.75
Material: HSS cast steel
Reference: 1900-1
Detachable steel handles Suitable for M3 - M12 taps Steel handle width 195 mm Die-cast zinc support for fixing the thread tap
Reference: 1983
Ratchet tap wrenches, for threading with manual thread taps. Adjustable to right, left and fixed. Total length 320 mm. For M5–M12 males
Reference: 932
3 males: Initial, central and finishing For thread/thread pitch: M5 x 0.8 Material: HSS cast steel
Reference: 1900-M11X1.25-B
2 males: Initial and finishing For thread/thread pitch: M11 x 1.25 Material: Tool steel (GCr15)
Reference: 1900-M12X0.75-B
2 males: Initial and finishing For thread/thread pitch: M12 x 0.75 Material: Tool steel (GCr15)
Reference: 1900-M10X1.0-B
2 males: Initial and finishing For thread/thread pitch: M10 x 1.0 Material: Tool steel (GCr15)
Reference: 1900-M8X1.25-B
2 males: Initial and finishing For thread/thread pitch: M8 x 1.25 Material: Tool steel (GCr15)
Reference: 1900
- tungsten steel - 2 male holders - 2 die holders - 1 T-type male swivel
Reference: 9161
Composition M3x0.5 / M5x0.8 / M7x0.75 / M10x1.25 / M3x0.6 / M5x0.9 / M7x1.0 / M10x1.5 / M4x0.7 / M6x0.75 / M8x1.0 / M12x1.5 / M4x0, 75 / M6x1.0 / M8x1.25 / M12x1.75
Reference: 1922
File to clean and fix imperfect threads. This file can be used for metric threads of approx. M8 to M40. Depending on the pitch of the thread, the corresponding side must be chosen. All sides are marked with their pitch between 0.75 mm up to 3.00 mm.
Reference: 1900-4
Steel handles, removable, steel handle width 380 mm. Cast zinc sheet support with 3 fixing screws for the dies
Reference: 1900-M12X1.25-B
2 males: Initial and finishing For thread/thread pitch: M12 x 1.25 Material: Tool steel (GCr15)
Reference: 1900-M12X1.5-
2 males: Initial and finishing For thread/thread pitch: M12 x 1.50 Material: Tool steel (GCr15)
Reference: S-HSSG16
16-piece metric tap and die tool set covering M3 to M12. Suitable for cleaning and cutting threads in mild steel and aluminum. Packaged in a convenient storage case.
Reference: 931
3 males: Initial, central and finishing For thread/thread pitch: M4 x 0.7 Material: HSS cast steel
Reference: 1900-M4X0.7-B
2 males: Initial and finishing For thread/thread pitch: M4 x 0.7 Material: Tool steel (GCr15)
3 males: Initial, central and finishing
For thread/thread pitch: M12 x 1.75
Material: HSS cast steel
